Rose electronics UltraVista Bedienerhandbuch

UltraVista LC Video controller/splitter 10707 Stancliff Road Phone: (281) 933-

MODELS 4 UltraVista LC Installation and Operations Manual UltraVista LC 1x4 model UltraVista LC 2x2 model UltraVista LC 3x3 model

UltraVista LC Installation and Operations Manual 5 Front Panel Indicators / Controls Video Out Indicators LEDs indicate which DVI output port has

6 UltraVista LC Installation and Operations Manual Rear Panel Connectors Power On / Off switch DC IN – 12V DC Sync In / Sync Out – Connects from a

INSTALLATION UltraVista LC Installation and Operations Manual 7 UltraVista LC Installation Installation of the UltraVista LC is an easy process. T

8 UltraVista LC Installation and Operations Manual The 3x3 unit’s video output mode is also determined by the input resolution of the video source.

UltraVista LC Installation and Operations Manual 9 Installing the LCD Displays Mount the LCD monitors as shown in figure 1, 2, 3 and 4. All displa

10 UltraVista LC Installation and Operations Manual Bezel compensation value calculation When all the displays have been mounted, measure the bezel

UltraVista LC Installation and Operations Manual 11 Mounting the UltraVista LC unit The UltraView LC unit can be placed on a desk or mounted on a h

12 UltraVista LC Installation and Operations Manual Figure 5. Serial Connection All models install and configure in the same manor.  Connect th

UltraVista LC Installation and Operations Manual 13 OSD Menu Structure To reset the UltraVista LC to factory defaults, Press the “UP”, “Down”, and

14 UltraVista LC Installation and Operations Manual To navigate within the OSD system, first press the menu button on the front panel. The Mask Con

UltraVista LC Installation and Operations Manual 15 Slave Mask Setting Mask Link = ON All slave units have the same settings Mask Link = OFF

16 UltraVista LC Installation and Operations Manual Settings OUT = Output resolution from the UltraVista LC MODE = Mode setting of the UltraVista

UltraVista LC Installation and Operations Manual 17 Information The information menu shows the current input and output resolutions. Slave Output

18 UltraVista LC Installation and Operations Manual Firmware Information FPGA = Current version of the FPGA chip CPLD = Current version of the CPL

Troubleshooting UltraVista LC Installation and Operations Manual 19 No Image on One Monitor  Check that the monitor is turned on  Check that the

Safety 20 UltraVista LC Installation and Operations Manual Safety The UltraVista LC has been tested for conformance to safety regulations and requir

Service UltraVista LC Installation and Operations Manual 21 Service Information Maintenance and Repair This Unit does not contain any internal user

Appendices 22 UltraVista LC Installation and Operations Manual Appendix A- General Specifications Inputs DVI Outputs – 4 x DVI / 9 x DVI

UltraVista LC Installation and Operations Manual 23

LIMITED WARRANTY Copyright  Rose Electronics 2010. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or tr

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 Internet: WWW.RO

HAZARDOUS MATERIAL DISCOLSURE The details provided below are to ensure that the product is compliant with the Peoples Republic of China RoHS standa

TABLE of CONTENTS Contents Page # Disclaimer ...

Figures Page # Figure 1. 2 x 2 Installation...

INTRODUCTION UltraVista LC Installation and Operations Manual 1 Disclaimer While every precaution has been taken in the preparation of this manual,

2 UltraVista LC Installation and Operations Manual Features  Supports Dual link DVI video input  Single-link DVI video outputs  Models

UltraVista LC Installation and Operations Manual 3 Compatibility A consumer grade graphic card with high-resolution dual link DVI output is require