Rose electronics CTP-4S Bedienerhandbuch

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 Internet: WWW

QUICK SETUP LIST – Parallel Units 6 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Parallel Set-Up 1. Connect the Caretaker Plus port 0 to your

CABLING CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL7 One of the most important steps in installing the Caretaker Plus is to connect the correct

8 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL to indicate entry into configuration mode. Entering configuration mode will stop data transfer

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL9 Configuration Menu Items In the examples below, <ENTER> means "press the ENTER key&quo

10 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Form Feed The form feed, when enabled, sends a form feed character to the shared device to eje

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL11 Exit This command is used to exit the configuration menu and return the unit to normal (data tra

12 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Reverse Channel Data Timeout This command (on the advanced features menu) determines whether o

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL13 Configuration Commands Configuration commands allow changing of the unit's setup parameters

14 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Protocol Command This command changes the communication protocol of a given port. If you enter

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL15 Parallel Enable Logic Command This command allows the Caretaker Plus to recognize when a compute

OPERATIONS 16 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Initial State Following the successful completion of the power up tests, the Caretak

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL17 Buffer Characteristics The switch may have a buffer memory of 16K, 256K, 512K, 1 megabyte, or 2

18 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Timeout The default setting of 20 seconds is sufficient for most applications. Some computers,

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL19 Initialization String The initialization string is used to reset the printer to a defined state

20 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Power Up Initial Display When powering on, the Caretaker Plus goes through a power up self-tes

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL21 Static Ram Read/Write Test The next test is for static ram. Since the Caretaker Plus has no stat

22 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Flow Control Display Mode (Serial Models Only) By pressing the ADVANCE switch during normal op

TROUBLESHOOTING CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL23 Troubleshooting Common Problems and Solutions I. Missing blocks of data on share

24 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL V. Port(s) do not time out A. 'Robust' X-on/X-off present. Some printers, parti

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL25 Maintenance and Repair The exterior surface of the unit may be wiped with a damp cloth to keep i

Limited Warranty Copyright  Rose Electronics 1990-2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,

DIAGNOSTICS 26 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Diagnostic Modes The Caretaker Plus has an extensive self-test diagnostic capabilit

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL27 Print Configuration/Test Pattern Function Holding both switches down at the end of test 4 causes

DIAGNOSTICS 28 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Long Test Without Loopback This group of tests are entered by pressing the select s

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL29 Long Test with Loopback This test is entered by pressing the advance switch only while powering

APPENDICES 30 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Appendix A: Serial Cabling The diagrams below show the Caretaker Plus pinout on the

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL31 Appendix B: Pinout Specifications Serial Models DB25 Female Pin Signal Name

32 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Appendix C: MP1000 Memory Board This memory board provides optional, add-on buffer expansion f

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL33 Installing the Board Carefully plug the expansion pins of the board (the first board, if using t

34 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Appendix D: Factory Defaults Upon receiving the Caretaker Plus from the factory, or restoring

Table of Contents Contents Disclaimer...

10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099

Introduction CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL1 Disclaimer While every precaution has been taken in the preparation of this manual, t

2 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Model Number and Options The Caretaker Plus consists of a switch unit and a separate wall mount

FRONT PANEL DISPLAY CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL3 Caretaker Plus Front Panel Display POWER LED is lit whenever the unit is p

QUICK SETUP LIST – Serial Units 4 CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL Serial Set-Up for PCs 1. Connect your PC to port 1 on the Caret

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL5 Caretaker Plus Rear Panel – Serial Model The diagram below shows the connector arrangement for mo